-- ₹

Roll Forming Machine quotation The roof And Wall Panel Roll Forming Machine is mainly used to produce various types of metal tile required for factories, stadiums, bus stations, exhibition pavilions, and other urban buildings. This product has strong durability, is not easy to damage, and the speed of rolling the steel plate is fast, which greatly saves time and labor costs. The finished steel plate after rolling is smooth without burrs and not easily deformed. Machine Specifications 1Coil TypePre-painted coil, Galvanized steel, or G500 G550 2Width1220mm or as per the client's request 3Thickness Range0.2-1mm 4Effective width1050mm or as per drawing 1Power RequirementVoltage(380V 50HZ),or according to client require Main Motor power5.5kw as per sheet thickness Cutter power5.5kw as per sheet thickness 2Forming speed10-15m/min 3Forming stations13 rows, as per finial machine 4Main Frame300H beam 5Sidewall thickness14mm 6Forming shaft diameter70mm 0.01mm-0.03mm(Grinding) 7Chain1inch chain drive or as per design 8Type of cuttingRoll formed and length-set cutting 9Control systemPLC control 10Install dimension(depend on the final design)7.4m 1.5m 1.3m 11The total weight (Approx)3.5T 12Roller materialHigh grade 45# steel, hard chrome plated 13Feeding systemGuide type 14Cutting bladeCr12 15Frequency changerDelta Manual DecoilerUsage: Mainly used to support steel coils, and manually uncoil and straighten the coil into the feeding table. Steel coil width: 940, 1200, 1220 mm. (According to your actual drawing) Loading capacity: 5T Inner diameter: 500-508mm Guiding DeviceAdopt a guiding bar and sliding block to control the width and position of the steel sheet. Pre-cutter used to cut sheet before roll forming, saving material. Roll Forming SystemMaterial of rollers: High grade 45# steel, roller surfaces polishing, hard plating chrome coated 0.05mm The polished surface and the heat treatment towards the molds also can keep the molding plate surface smooth and not easy to be marked when it is being stamped. the 5mm thick sleeve instead of galvanized pipe. To make the shaft and rollers more stable in order to make the profile Cutting deviceA. Adopts post cutting, the cutting blade material is Cr12 with quenched treatment, after cutting, there is no material wasted. B. Adopts welded frame for good rigidity. C. The cutting action is drove by the power from the hydraulic station which guarantees the procession of the cutting and low Hydraulic SystemIt is controlled by a gear wheel oil pump. After filling the hydraulic oil into the hydraulic oil tank, the pump drives the cutter machine to begin the cutting job. PLC Control SystemThe target piece`s length is adjustable and the digit of it can be adjusted. Computed mode has two modes: automatic and manual. The system is easy to operate and use PLC: Delta Run out tableTo receive the finished products. 2. Process Drawing Features for roll forming machine 1. Roof And Wall Panel Roll Forming Machine must use the high-number pulse input function, the high-number input performance is excellent, and the AB phase has a strong anti-interference ability. And use the fixed value interrupt function to ensure accuracy. 2. The detection part of the machine includes: the pulse encoder for detecting the length of the colored steel tile, the up and down travel switch for the pressing, the up and down travel switch for the cutter, the up and down operation buttons for the pressing, the up and down travel button for the cutter, and the emergency stop switch, hydraulic start-stop switch, etc. 3. The executive part of the machine has a frequency converter drive motor, a hydraulic station motor, two hydraulic solenoid valves for pressing, and two hydraulic solenoid valves for cutters. 4. The PLC has 14 inputs/10 relay outputs, which just meets the input and output requirements. With the KDN text screen, it can complete parameter setting, alarm display, help information, production data display, and so on.Roll Forming Machine quotation website:http://www.jr-rollformingmachine.com/roll-forming-machine/